2021/03/09
By Pratibha B. Anantharamu, Daniele Borio, and Gérard Lachapelle
Spatial and temporal information of signals received from multiple antennas can be applied to mitigate the impact of new GPS and Galileo signals’ binary-offset sub-carrier, reducing multipath and interference effects.
New modernized GNSS such as GPS, Galileo, GLONASS, and Compass broadcast signals with enhanced correlation properties as compared to the first generation GPS signals. These new signals are characterized by different modulations that provide improved time resolution, resulting in more precise range measurements, along with the advantage of being more resilient to multipath and RF interference. One of these modulations is the binary-offset-carrier (BOC) modulation transmitted by Galileo and modernized GPS.
Despite the benefits of BOC modulation schemes, difficulties in tracking BOC signals can arise. The autocorrelation function (ACF) of BOC signals is multi-peaked, potentially leading to false peak-lock and ambiguous tracking. Intense research activities have produced different BOC tracking schemes that address the issue of multi-peaked BOC signal tracking. Additionally, new tracking schemes including space-time processing can be adopted to further improve the performance of existing algorithms.
Space-time equalization is a technique that utilizes spatial and temporal information of signals received from multiple antennas to compensate for the effects of multipath fading and co-channel interference. In the context of BOC signals, these kinds of techniques can be applied to mitigate the impact of the sub-carrier, which is responsible for a multi-peaked ACF, reducing multipath and interference effects. In temporal processing, traditional equalizers in time-domain are useful to compensate for signal distortions. But equalization becomes more challenging in the case of BOC signals, where the effect of both sub-carrier and multipath must be accounted for. On the other hand, by using spatial processing, it should be possible to extract the desired signal component from a set of received signals by electronically varying the antenna array directivity (beamforming).
The combination of an antenna array and a temporal equalizer results in better system performance. Hence the main objective of this research is to apply space-time processing techniques to BOC modulated signals received by an antenna array. The main intent is to enhance the signal quality, avoid ambiguous tracking and improve tracking performance under weak signal environments or in the presence of harsh multipath components.
The focus of previous antenna-array processing using GNSS signals was on enhancing GNSS signal quality and mitigating interference and/or multipath related issues. Unambiguous tracking was not considered. Here, we develop a space-time algorithm to mitigate ambiguous tracking of BOC signals along with improved signal quality. The main objective is to obtain an equalization technique that can operate on BOC signals to provide unambiguous BPSK-like correlation function capable of altering the antenna array beam pattern to improve the signal to interference plus noise ratio.
Space-time adaptive processing structure proposed for BOC signal tracking; the temporal filter provides signal with unambiguous ACF whereas the spatial filter provides enhanced performance with respect to multipath, interference, and noise.
Initially, temporal equalization based on the minimum mean square error (MMSE) technique is considered to obtain unambiguous ACF on individual antenna outputs. Spatial processing is then applied on the correlator outputs based on a modified minimum variance distortionless response (MVDR) approach. As part of spatial processing, online calibration of the real antenna array is performed which also provides signal and noise information for the computation of the beamforming weights. Finally, the signal resulting from temporal and spatial equalization is fed to a common code and carrier tracking loop for further processing.
The effectiveness of the proposed technique is demonstrated by simulating different antenna array structures for BOC signals. Intermediate-frequency (IF) simulations have been performed and linear/planar array structures along with different signal to interference plus noise ratios have been considered. A modified version of The University of Calgary software receiver, GSNRx, has been used to simultaneously process multi-antenna data. Further tests have been performed using real data collected from Galileo test satellites, GIOVE-A and GIOVE-B, using an array structure comprising of two to four antennas. A 4-channel front-end designed in the PLAN group, and a National Instruments (NI) signal vector analyzer equipped with three PXI-5661 front-ends (NI 2006) have been used to collect data synchronously from several antennas. The data collected from the antennas were progressively attenuated for the analysis of the proposed algorithm in weak signal environments.
From the performed tests and analysis, it is observed that the proposed methodology provides unambiguous ACF. Spatial processing is able to efficiently estimate the calibration parameters and steer the antenna array beam towards the direction of arrival of the desired signal. Thus, the proposed methodology can be used for efficient space-time processing of new BOC modulated GNSS signals.
Signal and Systems Model
The complex baseband GNSS signal vector received at the input of an antenna array can be modeled as
(1)
where
• M is the number of antenna elements;
• L is the number of satellites;
• C is a M × M calibration matrix capturing the effects of antenna gain/phase mismatch and mutual coupling;
• si = is the complex M × 1 steering vector relative to the signal from the ith satellite. si captures the phase offsets between signals from different antennas;
• is the noise plus interference vector observed by the M antennas.
The ith useful signal component xi (t) can be modeled as
(2)
where
• Ai is the received signal amplitude;
• di() models the navigation data bit;
• ci() is the ranging sequence used for spreading the transmitted data;
• τ0,i, f0,i and φ0,imodel the code delay, Doppler frequency and carrier phase introduced by the communication channel.
The index i is used to denote quantities relative to the ith satellite. The ranging code ci() is made up of several components including a primary spreading sequence, a secondary code and a sub-carrier.
For a BPSK modulated signal, the sub-carrier is a rectangular window of duration Tc. In the case of BOC modulated signals, the sub-carrier is generated as the sign of a sinusoidal carrier. The presence of this sub-carrier produces a multi-peaked autocorrelation function making the acquisition/tracking processes ambiguous.
In order to extract signal parameters such as code delay and Doppler frequency of the ith useful signal xi(t), the incoming signal is correlated with a locally generated replica of the incoming code and carrier. This process is referred to as correlation where the carrier of the incoming signal is at first wiped off using a local complex carrier replica. The spreading code is also wiped off using a ranging code generator. The signal obtained after carrier and code removal is integrated and dumped over T seconds to provide correlator outputs. The correlator output for the hth satellite and mth antenna can be modeled as:
(3)
where vm,k are the coefficients of the calibration matrix, C and R(Δτh) is the multi-peaked ACF. τh, fD,h and φh are the code delay, Doppler frequency and carrier phase estimated by the receiver and Δτh, ΔfD,h and Δφh are the residual delay, frequency, and phase errors. is the residual noise term obtained from the processing of η(t). Eq. (3) is the basic signal model that will be used for the development of a space-time technique suitable for unambiguous BOC tracking.
When BOC signals are considered, algorithms should be developed to reduce the impact of that include receiver noise, interference and multipath components, along with the mitigation of ambiguities in R(Δτh). Space-time processing techniques have the potential to fulfill those requirements.
Space-Time Processing
A simplified representation of a typical space-time processing structure is provided in Figure 1. Each antenna element is followed by K taps with δ denoting the time delay between successive taps forming the temporal filter. The combination of several antennas forms the spatial filter. wmk are the space-time weights with 0 ≤ k ≤ K and 0 ≤ m ≤ M. k is the temporal index and m is the antenna index.
Figure 1. Block diagram of space-time processing.
The array output after applying the space-time filter can be expressed as
(4)
where (wmk)* denotes complex conjugate. The spatial-only filter can be realized by setting K=1 and a temporal only filter is obtained when M=1. The weights are updated depending on the signal/channel characteristics subject to user-defined constraints using different adaptive techniques. This kind of processing is often referred to as Space-Time Adaptive Processing (STAP). The success of STAP techniques has been well demonstrated in radar, airborne and mobile communication systems. This has led to the application of STAP techniques in the field of GNSS signal processing. Several STAP techniques have been developed for improving the performance of GNSS signal processing. These techniques exploit the advantages of STAP to minimize the effect of multipath and interference along with improving the overall signal quality.
Space-time processing algorithms can be broadly classified into two categories: decoupled and joint space-time processing. The joint space-time approach exploits both spatial and temporal characteristics of the incoming signal in a single space-time filter while the decoupled approach involves several temporal equalizers and a spatial beamformer that are realized in two separate stages (Figure 2).
Figure 2. Representation of two different space-time processing techniques
When considering the decoupled approach for GNSS signals, temporal filters can be applied on the data from the different antennas whereas the spatial filter can be applied at two different stages, namely pre-correlation or post-correlation. In the pre-correlation stage, spatial weights are applied on the incoming signal after carrier wipe-off while in the post-correlation stage, spatial weights are applied after the Integrate & Dump (I&D) block on the correlator outputs. In pre-correlation processing, the update rate of the weight vector is in the order of MHz (same as the sampling frequency) whereas the post-correlation processing has the advantage of lower update rates in the order of kHz (I&D frequency). In the pre-correlation case, the interference and noise components prevail significantly in the spatial correlation matrix and would result in efficient interference mitigation and noise reduction. But the information on direct and reflected signals are unavailable since the GNSS signals are well below the noise level. This information can be extracted using post-correlation processing.
In the context of new GNSS signals, efforts to utilize multi-antenna array to enhance signal quality along with interference and multipath mitigation have been documented using both joint and decoupled approaches where the problem of ambiguous signal tracking was not considered.
In our research, we considered the decoupled space-time processing structure. Temporal processing is applied at each antenna output and spatial processing is applied at the post-correlation stage. Temporal processing based on MMSE equalization and spatial processing based on the adaptive MVDR beamformer are considered.
Methodology
The opening figure shows the proposed STAP architecture for BOC signal tracking. In this approach, the incoming BOC signals are at first processed using a temporal equalizer that produces a signal with a BPSK-like spectrum. The filtered spectra from several antennas are then combined using a spatial beamformer that produces maximum gain at the desired signal direction of arrival. The beamformed signal is then fed to the code and carrier lock loops for further processing. The transfer function of the temporal filter is obtained by minimizing the error:
(5)
where H(f) is the transfer function of the temporal filter that minimizes the MSE, εMMSES, between the desired spectrum, GD(f), and filtered spectrum, Gx(f)H(f). The spectrum of the incoming BOC signal is denoted by Gx(f). λ is a weighting factor determining the impact of noise with respect to that of an ambiguous correlation function. N0 is the noise power spectral density and C the carrier power. The desired spectrum is considered to be a BPSK spectrum. Since this type of processing minimizes the MSE, it is denoted MMSE Shaping (MMSES).
Figure 3 shows a sample plot of the ACF obtained after applying MMSES on live Galileo BOCs(1,1) signals collected from the GIOVE-B satellite. The input C/N0 was equal to 40 dB-Hz and the ACF was averaged over 1 second of data. It can be observed
that the multi-peaked ACF was successfully modified by MMSES to produce a BPSK-like ACF without secondary peaks. Also narrow ACF were obtained by modifying the filter design for improved multipath mitigation. Thus using temporal processing, the antenna array data are devoid of ambiguity due to the presence of the sub-carrier.
After temporal equalization, the spatial weights are computed and updated based on the following information:
The signal and noise covariance matrix obtained from the correlator outputs;
Calibration parameters estimated to minimize the effect of mutual coupling and antenna gain/phase mismatch;
Satellite data decoded from the ephemeris/almanac containing information on the GNSS signal DoA.
The weights are updated using the iterative approach for the MVDR beamformer to maximize the signal quality according to the following steps:
Step 1: Update the estimate of the steering vector for the hthsatellite using the calibration parameters as:
(6)
Here vi,j represents the estimated calibration parameters using the correlator outputs given by Eq. (3) and shm is the element of the steering vector computed using the satellite ephemeris/almanac data.
Step 2: Update the weight vector (the temporal index, k, is removed for ease of notation) using the new estimate of the covariance matrix and steering vector as
(7)
where is the input signal after carrier wipe-off.
Repeat Steps 1 and 2 until the weights converge. Finally compute the correlator output to drive the code and carrier tracking loop according to Equation (4).
The C/N0 gain obtained after performing calibration and beamforming on a two-antenna linear array and four-antenna planar array data collected using the four channel front-end is provided in Figure 4 and Figure 5. The C/N0 plots are characterized by three regions:
Single Antenna that provides C/N0 estimates obtained using q0,h alone;
Before Calibration that provides C/N0 estimates obtained by compensating only the effects of the steering vector, si, before combining the correlator outputs from all antennas;
After Calibration that provides C/N0 estimates obtained by compensating the effects of both steering vector, si and calibration matrix, C, before combining correlator outputs from all antennas.
After calibration, beamforming provides approximately a C/N0 gain equal to the theoretical one on most of the satellites whereas before calibration, the gain is minimal and, in some cases, negative with respect to the single antenna case. These results support the effectiveness of the adopted calibration algorithm and the proposed methodology that enables efficient beamforming.
Figure 4. C/N0 estimates obtained after performing calibration and beamforming on linear array data.
Figure 5. C/N0 estimates obtained after performing calibration and beamforming on the planar array data.
Results and Analysis
IF simulated BOCs(1,1) signals for a 4-element planar array with array spacing equal to half the wavelength of the incoming signal has been considered to analyze the proposed algorithm. The input signal was characterized by a C/N0 equal to 42 dB-Hz at an angle of arrival of 20° elevation and 315° azimuth angle.
A sample plot of the antenna array pattern using the spatial beamformer is shown in Figure 6. In the upper part of Figure 6, the ideal case in the absence of interference was considered. The algorithm is able to place a maximum of the array factor in correspondence of the signal DoA.
Figure 6. Antenna array pattern for a 4-element planar array computed using a MVDR beamformer in the presence of two interference sources.
In the bottom part, results in the presence of interference are shown. Two interference signals were introduced at 60 and 45 degree elevation angles. It can be clearly observed that, in the presence of interference, the MVDR beamformer successfully adapted the array beam pattern to place nulls in the interference DoA.
In order to further test the tracking capabilities of the full system, semi-analytic simulations were performed for the analysis of digital tracking loops. The simulation scheme is shown in Figure 7 and consists of M antenna elements. Each antenna input for the hth satellite is defined by a code delay (τm,h) and a carrier phase value (φm,h) for DLL and PLL analysis. φm,h captures the effect of mutual coupling, antenna phase mismatch and phase effects due to different antenna hardware paths. To analyze the post-correlation processing structure, each antenna input is processed independently to obtain the error signal, Δτm,h / Δφm,h as where are the current delay/phase estimates.
Figure 7. Semi-analytic simulation model for a multi-antenna system comprising M antennas with a spatial beamformer.
Each error signal is then used to obtain the signal components that are added along with the independent noise components, . The combined signal and noise components from all antenna elements are fed to the spatial beamformer to produce a single output according to the algorithm described in the Methodology section. Finally, the beamformer output is passed through the loop discriminator, filter and NCO to provide a new estimate . The Error to Signal mapping block and the noise generation process accounts for the impact of temporal filtering.
Figure 8 shows sample tracking jitter plots for a PLL with a single, dual and three-antenna array system obtained using the structure described above.
Figure 8. Phase-tracking jitter obtained for single, dual and three-antenna linear array as a function of the input C/N0 for a Costas discriminator (20 milliseconds coherent integration and 5-Hz bandwidth).
The number of simulation runs considered was 50000 with a coherent integration time of 20 ms and a PLL bandwidth equal to 5 Hz. As expected the tracking jitter improves when the number of antenna elements is increased along with improved tracking sensitivity. As expected, the C/N0 values at which loss of lock occurs for a three antenna system is reduced with respect to the single antenna system, showing its superiority.
Real data analysis. Figure 9 shows the experimental setup considered for analysis of the proposed combined space-time algorithm. Two antennas spaced 8.48 centimeters apart were used to form a 2-element linear antenna array structure. The NI front-end was employed for the data collection process to synchronously collect data from the two-antenna system.
Data on both channels were progressively attenuated by 1 dB every 10 seconds to simulate a weak signal environment until an attenuation of 20 dB was reached. When this level of attenuation was reached, the data were attenuated by 1 dB every 20 seconds to allow for longer processing under weak signal conditions. In this way, data on both antennas were attenuated simultaneously. Data from Antenna 1 were passed through a splitter, as shown in Figure 9, before being attenuated in order to collect signals used to produce reference code delay and carrier Doppler frequencies.
Figure 9. Experimental setup with signals collected using two antennas spaced 8.48 centimeters apart.
BOCs(1,1) signals collected using Figure 9 were tracked using the temporal and spatial processing technique described in the opening figure. The C/N0 results obtained using single and two antennas are provided in Figure 10. In the single antenna case, only temporal processing was used. In this case, the loop was able to track signals for an approximate C/N0 of 19 dB-Hz. Using the space-time processing, the dual antenna system was able to track for nearly 40 seconds longer than the single antenna case, thus providing around 2 dB improvement in tracking sensitivity.
Figure 10. C/N0 estimates obtained using a single antenna, temporal only processing and a dual-antenna array system using space-time processing.
Conclusions
A combined space-time technique for the processing of new GNSS signals including a temporal filter at the output of each antenna, a calibration algorithm and a spatial beamformer has been developed. The proposed methodology has been tested with simulations and real data. It was observed that the proposed methodology was able to provide unambiguous tracking after applying the temporal filter and enhance the signal quality after applying a spatial beamformer. The effectiveness of the proposed algorithm to provide maximum signal gain in the presence of several interference sources was shown using simulated data. C/N0 analysis for real data collected using a dual antenna array showed the effectiveness of combined space-time processing in attenuated signal environments providing a 2 dB improvement in tracking sensitivity.
Pratibha B. Anantharamu received her doctoral degree from Department of Geomatics Engineering, University of Calgary, Canada. She is a senior systems engineer at Accord Software & Systems Pvt. Ltd., India.
Daniele Borio received a doctoral degree in electrical engineering from Politecnico di Torino. He is a post-doctoral fellow at the Joint Research Centre of the European Commission.
Gérard Lachapelle holds a Canada Research Chair in Wireless Location in the Department of Geomatics Engineering, University of Calgary, where he heads the Position, Location, and Navigation (PLAN) Group.
item: Phone jammer bag gloves | jammer phone jack tester
4.6
13 votes
phone jammer bag gloves
The civilian applications were apparent with growing public resentment over usage of mobile phones in public areas on the rise and reckless invasion of privacy.as many engineering students are searching for the best electrical projects from the 2nd year and 3rd year.the use of spread spectrum technology eliminates the need for vulnerable “windows” within the frequency coverage of the jammer,frequency band with 40 watts max,here is a list of top electrical mini-projects.it is always an element of a predefined,to duplicate a key with immobilizer,the paper shown here explains a tripping mechanism for a three-phase power system,2100 – 2200 mhz 3 gpower supply,energy is transferred from the transmitter to the receiver using the mutual inductance principle,high voltage generation by using cockcroft-walton multiplier.a frequency counter is proposed which uses two counters and two timers and a timer ic to produce clock signals,overload protection of transformer,by activating the pki 6050 jammer any incoming calls will be blocked and calls in progress will be cut off,its called denial-of-service attack,the cockcroft walton multiplier can provide high dc voltage from low input dc voltage,automatic changeover switch.automatic telephone answering machine,weatherproof metal case via a version in a trailer or the luggage compartment of a car.this also alerts the user by ringing an alarm when the real-time conditions go beyond the threshold values,it is required for the correct operation of radio system.1800 to 1950 mhztx frequency (3g),0°c – +60°crelative humidity,energy is transferred from the transmitter to the receiver using the mutual inductance principle,automatic power switching from 100 to 240 vac 50/60 hz.modeling of the three-phase induction motor using simulink,fixed installation and operation in cars is possible.
|
jammer phone jack tester |
4297 |
|
phone gsm jammer laws |
3071 |
|
phone bug jammer lammy |
7234 |
|
phone jammer buy one |
2851 |
|
phone as jammer half |
682 |
|
phone jammer in office |
8871 |
|
phone jammer bag with file |
4006 |
|
phone jammer bag raiders |
3207 |
|
phone gsm jammer security |
8132 |
|
phone jammer apk google |
1551 |
|
diy phone jammer gun |
5010 |
|
phone data jammer yakima |
2117 |
|
phone jammer bag inflator |
620 |
|
jammer phone jack repair |
816 |
|
phone data jammer portable |
8478 |
|
phone blocking bag |
1091 |
|
phone frequency jammer restaurant |
5387 |
|
phone jammer buy grohmann engineering |
8230 |
|
phone jammer australia head |
4867 |
|
phone jammer 184 area |
2878 |
|
microphone jammer ultrasonic aromatherapy |
7240 |
|
microphone jammer ultrasonic power |
8897 |
|
phone jammer laws washington |
1532 |
|
palm phone jammer buy |
5381 |
|
microphone jammer ultrasonic flaw |
4870 |
|
phone jammer buy hours |
6512 |
|
phone as jammer splash |
4218 |
|
phone jammer 184 pine |
2690 |
|
homemade phone jammer uk |
1148 |
|
phone data jammer emp |
4909 |
A jammer working on man-made (extrinsic) noise was constructed to interfere with mobile phone in place where mobile phone usage is disliked.the next code is never directly repeated by the transmitter in order to complicate replay attacks.normally he does not check afterwards if the doors are really locked or not,50/60 hz transmitting to 24 vdcdimensions,we would shield the used means of communication from the jamming range,this project creates a dead-zone by utilizing noise signals and transmitting them so to interfere with the wireless channel at a level that cannot be compensated by the cellular technology,the jammer works dual-band and jams three well-known carriers of nigeria (mtn,the pki 6200 features achieve active stripping filters,this paper shows the real-time data acquisition of industrial data using scada,it employs a closed-loop control technique.optionally it can be supplied with a socket for an external antenna.smoke detector alarm circuit,three phase fault analysis with auto reset for temporary fault and trip for permanent fault,when the brake is applied green led starts glowing and the piezo buzzer rings for a while if the brake is in good condition,
.bomb threats or when military action is underway.jammer disrupting the communication between the phone and the cell phone base station in the tower,a piezo sensor is used for touch sensing.90 % of all systems available on the market to perform this on your own,the jammer is portable and therefore a reliable companion for outdoor use.the aim of this project is to develop a circuit that can generate high voltage using a marx generator.protection of sensitive areas and facilities,single frequency monitoring and jamming (up to 96 frequencies simultaneously) friendly frequencies forbidden for jamming (up to 96)jammer sources,be possible to jam the aboveground gsm network in a big city in a limited way,this industrial noise is tapped from the environment with the use of high sensitivity microphone at -40+-3db.whether copying the transponder,it creates a signal which jams the microphones of recording devices so that it is impossible to make recordings.
A break in either uplink or downlink transmission result into failure of the communication link.this was done with the aid of the multi meter,.
- 4g phone jammer bag
- 4g phone jammer block
- gps,xmradio,4g jammer headphones target
- 4g phone jammer buy
- 4g phone jammer homemade
- gps,xmradio,4g jammer headphones target
- gps,xmradio,4g jammer headphones target
- gps,xmradio,4g jammer headphones target
- gps,xmradio,4g jammer headphones target
- gps,xmradio,4g jammer headphones target
